Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to professional auto locksmiths who have the right equipment and technical knowledge. They can make and program new keys quicker than a dealership and at a lower cost.
If your key fob has stopped locking or unlocking your doors, it is likely due to a dead battery in the coin. However, there are many other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, as well as preventing it from starting the engine. In this case, you will need to choose the alternate method to start that is described in the owner's manual.
The spark plugs can also be worn out. The spark plugs are responsible for sparking the fuel that ignites the engine. They only last for a certain amount of time. They will eventually break down if they're not used enough.
Fortunately, there's an easy solution to this issue. The best way to solve this issue is to measure the voltage of your car battery using a multimeter. If the voltage is less than 11,5 volts then it's time to replace it. It is also essential to clean the contacts of the battery when it has corrosion. This can be accomplished by removing the rubber cover from the two battery terminals and then using a wirebrush to eliminate any damaged parts of the battery. Then, you must reconnect the positive pole cables to the negative.
Water Damage
If your 208 isn't starting and the battery is not flat then you should check whether the spark plugs are in good working order. You may find that they're dirty and don't spark. The spark plugs can be cleaned in a workshop.
Peugeot cars use a transponder key that works with the car's immobiliser system. This ensures only the correct key is able to turn the engine. If the chip in the Peugeot key is damaged, it won't send the proper signal to the vehicle.
This is a common problem that is caused by water damage. This is most common in colder climates. the vehicle may have been exposed to rain or snow. If this is the case, contact a reputable auto locksmith who will have all the equipment and tools needed to reprogram the new key. peugeot car key will also have all the latest technology and equipment required to make the Peugeot smart key. The process should take no more than 15 minutes.
Contacts for the battery that are defective
Peugeot changed from the old carbon encased transponder chips and introduced a new type of chip that uses electronic components within a circuit board. This new system works well when it's brand new, however, over time, the circuit boards begin to deteriorate and stop working properly.
This could prevent the immobiliser chip from activating the immobiliser chip, causing your car not to start. Contact an Peugeot specialist, or a locksmith, if this is the case.
A common issue is when the battery inside the key fob begins to fail. This causes the blade of the key to stop feeding into your lock. A locksmith in your car will replace the battery and then cut a new blade for you. This is a simple fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, being exposed to a sudden downpour or accidentally washing it, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer which regulates the central locking system of your Peugeot vehicle.
Rubber seals on the key fob stop water from getting to the electronic chip. The chip can be damaged by water in the event that it is exposed water for a long time. Submerging the key fob into ocean water at the beach or throwing it into the pool can be especially damaging because of the high salt content.
If your Peugeot spare key fob stops working it is necessary to have the module replaced. This is only done by an Peugeot specialist or an expert auto locksmith. Peugeot keys unlike other automobiles, are secured by an immobilizer system. This requires the right codes to start the car. It is for this reason that you should only trust an authorized Peugeot locksmith to create and program an alternative.
Computer on board is not working properly
The computer on board of your Peugeot is responsible for various systems inside your car, including power windows and airbags. If something goes wrong with these systems, it will usually display a code that identifies the issue. The code is stored within the system until the issue is resolved. This can often mean that the on-board computers to be replaced.
One of the most common causes of the light coming on is loose or corroded connections in the airbag sensor. This could be due to wear and tear, aging or exposure to moisture and salt. It is crucial to get this issue resolved as soon as you can, since an airbag that is malfunctioning can be dangerous in the event an accident.
If your Peugeot is showing a card not detected error, the battery inside the key fob may be dead or weak. This will stop the key fob from sending a signal that will disable the vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then attempting to start your vehicle. If this doesn't work it is likely that the battery must be replaced.